Downcut bit suitable for plywood, dibond, plated DM and melamine board

Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Solid carbide tool with a micro-polished right-hand helix, specially designed to achieve high-quality surface finishes on thermoplastics, even at high feed rates. Its innovative geometry allows for optimal finishes in a single cutting pass on materials such as:

· Cast or extruded acrylic.
· PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.
· Solid Surface materials: Corian®, Krion®, etc.

High wear-resistant solid carbide tool, designed with an innovative gradual-action chip breaker. Acts as a heat dissipator and cutting stabiliser, allowing machining of high-density materials at high feed rates, achieving quality finishes without marking the edge. Recommended for cutting:

· High-pressure laminates (HPL, Trespa®, Formica®).
· Bakelite.
· High-density cellulose laminates.
· Hardwoods and phenolic plywood.

RH: right-hand helix.
LH: left-hand helix.

High-precision tool holder for CNC machines

D: cutting diameter d: gripping diameter T: total length

V-shaped bit suitable for wood and MDF

It allows to make V engravings and chamfers in the edges of the wood. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Planing bit suitable for wood and MDF

It allows to rectify large surfaces quickly and efficiently. Specific for works that require a lot of flatness and to review the waste bed. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

V-groove bit suitable for wood and MDF

It allows to make precise engravings and bows in the edges. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Engraving bit suitable for wood, plastic and aluminium

It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)

Straight cutting bit suitable for wood, melamine and foams

Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Upcut bit suitable for wood, methacrylate and PVC

Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Upcut bit suitable for wood, methacrylate and PVC

Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.

D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)

Red Fox and Ion Plasma offer the possibility of installing adjustable steel legs, with a 780 mm height, and a computer support. They are the perfect complement to implement it independently in the workshop.