



Reference: 0503
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 4 mm |
L | 32 mm |
T | 60 mm |
C | 4 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Security policy
Shipping policy
Dirección de corte recto, da un buen acabado superficial sin comprometer la capacidad de corte. No descascarilla la cara superior y pueden utilizarse profundidades de pasado similares al corte positivo.
D | (diámetro de corte) | 8mm |
L | (largo de corte) | 50mm |
T | (largo total) | 100mm |
C | (diámetro caña) | 8mm |
Fabricada en acero de tungsteno.
8436582312200
D | 33 mm |
d | 8 mm |
T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
It allows to rectify large surfaces quickly and efficiently. Specific for works that require a lot of flatness and to review the waste bed. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 30 mm |
L | 15 mm |
T | - |
C | 6 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
D | 33 mm |
d | 5 mm |
T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
This adapter allows to use 3,17 mm or 3 mm bits on the milling motor.
D | 6 mm |
d | 4 mm |
T | 25 mm |
D: cutting diameter d: gripping diameter T: total length
D | 33 mm |
d | 12,7 mm |
T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 2 mm |
L | 22 mm |
T | 45 mm |
C | 3,175 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
D | 33 mm |
d | 3,175 mm |
T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
D | 0,6 mm |
A | 70º |
T | 45 mm |
C | 6 mm |
N | 2 |
D: cutting diameter A: angle T: total length C: shank diameter N: flutes number (or cutting edges)
It allows 3D work that requires a 3 mm radius. Stands out for its durability. Made of tungsten carbide (TC), a harder material than HSS. Better cutting edge conservation and superior bit durability.
D | 12 mm |
L | 24 mm |
T | 75 mm |
C | 12 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 8 mm |
L | 32 mm |
T | 70 mm |
C | 8 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 25 mm |
L | - |
T | - |
C | 6 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D | 4 mm |
L | 32 mm |
T | 60 mm |
C | 4 mm |
N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)