Straight cutting bit suitable for wood, melamine and foams
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
1,5 mm
L
8 mm
T
38,5 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut bit suitable for plywood, dibond, plated DM and melamine board
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
32 mm
T
65 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
22 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
72 mm
T
120 mm
C
10 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
2 mm
L
22 mm
T
45 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
72 mm
T
100 mm
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
32 mm
T
80 mm
C
10 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
25 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
8 mm
L
62 mm
T
100 mm
C
8 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
1,5 mm
L
8 mm
T
38,5 mm
C
3,175 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut bit suitable for plywood, dibond, plated DM and melamine board
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
32 mm
T
65 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
