Reference: 843658231206
Security policy
Shipping policy
| D | 21 mm |
| d | 12,7 mm |
| T | 31,5 mm |
D: cutting diameter d: gripping diameter T: total length
| D | 33 mm |
| d | 10 mm |
| T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of tungsten carbide (TC), a harder material than HSS. Better cutting edge conservation and superior bit durability.
| D | 8 mm |
| L | 26 mm |
| T | - |
| C | 12,7 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 3,175 mm |
| L | 12 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 25 mm |
| T | 55 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 3 mm |
| L | 8 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 32 mm |
| T | 65 mm |
| C | 6 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 32 mm |
| T | 65 mm |
| C | 6 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
| D | 33 mm |
| d | 4 mm |
| T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 72 mm |
| T | 100 mm |
| C | 6 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 1,5 mm |
| L | 8 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Lengthen the tool for milling in hard-to-reach areas. It fits on a 20 mm ER32 collet and allows its cutting to achieve the necessary length. Includes an ER20 collet nut and can be used as ER32 to ER20 converter.
| D | 20 mm |
| L | 100 mm |
| C | ER20A |
D: cutting diameter L: cutting length C: shank diameter
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 72 mm |
| T | 100 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
| D | 21 mm |
| d | 5 mm |
| T | 31,5 mm |
D: cutting diameter d: gripping diameter T: total length
What types of end mills can we use in the Red Fox CNC milling machine series?
Español
English GB
