Engraving bit suitable for high hardness materials
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
D
0,6 mm
A
120º
T
45 mm
C
6 mm
N
2
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut bit suitable for plywood, dibond, plated DM and melamine board
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting bit suitable for wood, melamine and foams
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
3,175 mm
L
32 mm
T
60 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Engraving bit suitable for wood, plastic and aluminium
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,5 mm
A
45º
T
33 mm
C
3,175 mm
N
2
D: cutting diameter A: angle T: total length C: shank diameter N: flutes number (or cutting edges)
Engraving bit suitable for high hardness materials
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
D
0,6 mm
A
90º
T
45 mm
C
6 mm
N
2
D: cutting diameter A: angle T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
8 mm
L
32 mm
T
70 mm
C
8 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make V engravings and chamfers in the edges of the wood. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2/22 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make V engravings and chamfers in the edges of the wood. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2/22 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to rectify large surfaces quickly and efficiently. Specific for works that require a lot of flatness and to review the waste bed. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
16 mm
L
10 mm
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
32 mm
T
80 mm
C
10 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Engraving bit suitable for high hardness materials
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
D
0,6 mm
A
120º
T
45 mm
C
6 mm
N
2
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
