Engraving bit suitable for wood, plastic and aluminium
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2 mm
A
45º
T
33 mm
C
3,175 mm
N
2
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting bit suitable for wood, melamine and foams
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
8 mm
L
32 mm
T
60 mm
C
8 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
32 mm
T
65 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut bit suitable for plywood, dibond, plated DM and melamine board
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
26 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Engraving bit suitable for wood, plastic and aluminium
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2 mm
A
25º
T
33 mm
C
3,175 mm
N
2
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
It allows 3D work that requires a 3 mm radius. Stands out for its durability. Made of tungsten carbide (TC), a harder material than HSS. Better cutting edge conservation and superior bit durability.
D
6 mm
L
12 mm
T
50 mm
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to rectify large surfaces quickly and efficiently. Specific for works that require a lot of flatness and to review the waste bed. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
30 mm
L
15 mm
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make V engravings and chamfers in the edges of the wood. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2/22 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
2 mm
L
8 mm
T
38,5 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
32 mm
T
60 mm
C
4 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Nuestros clientes opinan
5
4
3
2
1
0.00 / 5
0 Comments
Your review appreciation cannot be sent
Report comment
Are you sure that you want to report this comment?
Report sent
Your report has been submitted and will be considered by a moderator.
Your report cannot be sent
Write your review
Review sent
Your comment has been submitted and will be available once approved by a moderator.
Engraving bit suitable for wood, plastic and aluminium
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
0,2 mm
A
45º
T
33 mm
C
3,175 mm
N
2
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
