Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
72 mm
T
120 mm
C
10 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
32 mm
T
65 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
72 mm
T
120 mm
C
10 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
1 mm
L
4 mm
T
38,5 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
3 mm
L
42 mm
T
72 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
25 mm
L
-
T
-
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
1,5 mm
L
8 mm
T
38,5 mm
C
3,175 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
72 mm
T
100 mm
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
4 mm
L
15 mm
T
45 mm
C
4 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Nuestros clientes opinan
5
4
3
2
1
0.00 / 5
0 Comments
Your review appreciation cannot be sent
Report comment
Are you sure that you want to report this comment?
Report sent
Your report has been submitted and will be considered by a moderator.
Your report cannot be sent
Write your review
Review sent
Your comment has been submitted and will be available once approved by a moderator.
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
10 mm
L
72 mm
T
120 mm
C
10 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
