Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
17 mm
T
50 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
32 mm
T
65 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Lengthen the tool for milling in hard-to-reach areas. It fits on a 20 mm ER32 collet and allows its cutting to achieve the necessary length. Includes an ER20 collet nut and can be used as ER32 to ER20 converter.
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
2 mm
L
8 mm
T
38,5 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Downcut bit suitable for plywood, dibond, plated DM and melamine board
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
3,175 mm
L
22 mm
T
45 mm
C
3,175 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Composites cutting bit suitable for carbon, methacrylate, plastics and epoxy
It has multiple diamond-shaped teeth and is specially designed for cutting composite materials. Good surface finish and long service life. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
25 mm
T
55 mm
C
6 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
8 mm
L
32 mm
T
70 mm
C
8 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting bit suitable for wood, melamine and foams
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
3,175 mm
L
32 mm
T
60 mm
C
3,175 mm
N
2
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Fresa de corte recto indicada para madera, melamina y espumas
Dirección de corte recto, da un buen acabado superficial sin comprometer la capacidad de corte. No descascarilla la cara superior y pueden utilizarse profundidades de pasado similares al corte positivo.
D
(diámetro de corte)
8mm
L
(largo de corte)
50mm
T
(largo total)
100mm
C
(diámetro caña)
8mm
Fabricada en acero de tungsteno.
8436582312200
Nuestros clientes opinan
5
4
3
2
1
0.00 / 5
0 Comments
Your review appreciation cannot be sent
Report comment
Are you sure that you want to report this comment?
Report sent
Your report has been submitted and will be considered by a moderator.
Your report cannot be sent
Write your review
Review sent
Your comment has been submitted and will be available once approved by a moderator.
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
D
6 mm
L
17 mm
T
50 mm
C
6 mm
N
1
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
