Reference: 0302
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 4 mm |
| L | 15 mm |
| T | 45 mm |
| C | 4 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Security policy
Shipping policy
| D | 21 mm |
| d | 5 mm |
| T | 31,5 mm |
D: cutting diameter d: gripping diameter T: total length
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
| D | 0,6 mm |
| A | 70º |
| T | 45 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter A: angle T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 8 mm |
| L | 25 mm |
| T | 60 mm |
| C | 8 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 10 mm |
| L | 32 mm |
| T | 80 mm |
| C | 10 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 10 mm |
| L | 72 mm |
| T | 120 mm |
| C | 10 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
| D | 33 mm |
| d | 4 mm |
| T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
This adapter allows to use 3,17 mm or 3 mm bits on the milling motor.
| D | 6 mm |
| d | 4 mm |
| T | 25 mm |
D: cutting diameter d: gripping diameter T: total length
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 1,5 mm |
| L | 8 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 32 mm |
| T | 65 mm |
| C | 6 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 4 mm |
| L | 32 mm |
| T | 60 mm |
| C | 4 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 72 mm |
| T | 100 mm |
| C | 6 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
| D | 21 mm |
| d | 6 mm |
| T | 31,5 mm |
D: cutting diameter d: gripping diameter T: total length
What types of end mills can we use in the Red Fox CNC milling machine series?
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp on laminated materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 4 mm |
| L | 15 mm |
| T | 45 mm |
| C | 4 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
