Reference: 0201
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 1,5 mm |
| L | 6 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Security policy
Shipping policy
This adapter allows to use 3,17 mm or 3 mm bits on the milling motor.
| D | 6 mm |
| d | 4 mm |
| T | 25 mm |
D: cutting diameter d: gripping diameter T: total length
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 8 mm |
| L | 32 mm |
| T | 60 mm |
| C | 8 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Straight cutting direction, gives a good surface finish keeping cutting capacity. It doesn't flake the upper face and allows to use passing depths similar to those of upcut. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 3,175 mm |
| L | 32 mm |
| T | 60 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 0,5 mm |
| A | 25º |
| T | 33 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter A: angle T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make high-precision V engravings on multiple materials. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 0,2 mm |
| A | 25º |
| T | 33 mm |
| C | 3,175 mm |
| N | 2 |
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 32 mm |
| T | 65 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to make hihg-precision V engravings. Stands out for its durability. Made of diamond coating on CT (PCT). The hardest material and with the highest edge durability; Specific for hard materials.
| D | 0,6 mm |
| A | 120º |
| T | 45 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter A: Angle T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 4 mm |
| L | 32 mm |
| T | 60 mm |
| C | 4 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
It allows to create moldings with different profiles in a simple way. Stands out for its durability. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 25 mm |
| L | - |
| T | - |
| C | 6 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
| D | 33 mm |
| d | 3,175 mm |
| T | 40 mm |
D: cutting diameter d: gripping diameter T: total length
| D | 21 mm |
| d | 6 mm |
| T | 31,5 mm |
D: cutting diameter d: gripping diameter T: total length
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 3,175 mm |
| L | 22 mm |
| T | 45 mm |
| C | 3,175 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. Possible chipping on top of some solid woods such as pine. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 8 mm |
| L | 62 mm |
| T | 100 mm |
| C | 8 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Upcut direction, helps evacuation and facilitates cutting. It can leave some wisp and a slightly rough finish. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 6 mm |
| L | 72 mm |
| T | 100 mm |
| C | 6 mm |
| N | 2 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
What types of end mills can we use in the Red Fox CNC milling machine series?
Downcut direction, offers a better surface finish. Lower passing depths are recommended. Ideal for materials that chip at the top or are composed of layers. Made of high-speed steel (HSS), a low-cost standard unhardened material used for most materials and works.
| D | 1,5 mm |
| L | 6 mm |
| T | 38,5 mm |
| C | 3,175 mm |
| N | 1 |
D: cutting diameter L: cutting length T: total length C: shank diameter N: flutes number (or cutting edges)
Español
English GB
